Newest Products (834)

12 x 500ml Endotherm Energy Saving & Carbon Emission Reducing Additive Typical 10-15% savings #10: ENDOTHERMX12 Endotherm Brochure Endotherm Installation Manual Changing the properties of water to improve energy efficiency. EndoTherm is a unique, multi-award winning energy saving hydronic additive independently proven to save up to 15% on space heating energy consumption. How much Endotherm should be used: 2 x 500ml bottles are sufficient for a medium to large 3-4 bed detached property. For more accurate sizing Endotherm should equate to 1% of total system volume. When should Endotherm be added: The ideal time to minimise installation costs will be when the heating system is being serviced. However, if the system won't be serviced before the winter time then it could be better to start enjoying the savings straight away. Water is used in heating systems as it is a good heat transfer medium that is abundant and low-cost. EndoTherm optimises water to influence heating system performance. Although water is abundant and low cost, its thermophysical properties can be improved upon.EndoTherm interacts with water’s hydrogen bond network to improve its thermophysical properties to maximise the ability of heating systems to deliver heat to the locations required at the times it is needed.These changes can increase the rates at which rooms reach temperature and improve the ability of the heating system to respond to changes in demand.This allows heating systems to better deliver heat to the right places, and at the right times to maximise system efficiency. Independently Proven EndoTherm has been rigorously tested with savings confirmed by multiple third party Research & Development laboratories and facilities. Easy to Install EndoTherm requires no system downtime and can be installed, like an inhibitor, in just 10-15 minutes. Non - Corrosive EndoTherm is non-corrosive to heating system components in use and is non-hazardous with no discharge requirements. Award Winning & Recognised EndoTherm is a multi-award winning technology with confirmed compatibility with leading boiler and inhibitor brands. Carbon Emission Reduction As EndoTherm reduces heating energy consumption, greenhouse gas emissions are also reduced which is vital to achieve net zero targets. 100% Organic EndoTherm is made from 100% organic materials and is responsible for 0.58Kg embodied carbon which is offset in under a day of use. EndoTherm is installed at 1% of total system volume using the same methodology as traditional corrosion inhibitors. Or 2 x 500ml bottles for a typical 3-4 bedroom home. These guidelines are based on steel flat panel radiators More EndoTherm may be required if higher water volume heat emitters like traditional cast iron radiators.Research has shown that EndoTherm remains stable and is able to sustain at a functional concentration within a closed heating system circuit for 10+ years provided no significant fluid loss (and subsequent refilling causing EndoTherm dilution) has occurred due to leaks or maintenance.

SolarEdge Home Battery Home Battery 48V V2 - 3PH Low Voltage 5x 4.6kWh module = 23kWh #2: SE-BATTERY-4.6kWH-02-5-23 SolarEdge 4.6kWh Datasheet SolarEdge 4.6kWh Manual SolarEdge 4.6kWh Warranty This product contains 5 x SolarEdge Home Battery 48V V2 - 3PH Low Voltage 4.6kWh module BAT-05K48M0B-02 - Three Phase Inverter Connection Only DC coupled battery featuring superior overall system efficiency, generating more energy to store and use for on-grid and backup* power application. Scalable solution that enables to stack up multiple battery modules per inverter for increased capacity (up to 23 kWh). Integrates seamlessly with the complete SolarEdge Home ecosystem, offering a single source for warranty, support and training, to streamlined logistics & operations. Solar, storage, EV charging, and smart devices all monitored and managed by a single app for optimized production, consumption, and backup* power. Includes enhanced safety features for battery protection. Simple plug and play installation, with automatic SetApp-based configuration Weight: 305 kgBattery Type: Lithium IonNominal Energy: 13800 WhDepth of discharge: 90.00 %Voltage: 51 VContinuous Discharge Rate (Normal Use): 5000 WMaximum Discharge Rate (5 Minutes): 5000 WSurge Discharge Rate (15 Seconds): 5000 WMaximum Charge Rate (5 Minutes): 5000 W

GivEnergy PE Bonding Kit for Gen3 Hybrid Inverters 2: GIV-PE-KIT-G3 GivEnergy Bonding Kit Please note: This item can only be purchased with a GivEnergy Generation 3 hybrid. ITS will be unable to process orders featuring this part code if a Generation 3 hybrid does not exist within the order. GivEnergy PE Bonding Kit for Gen3 Hybrid Inverters The GIV-PE-KIT-G3 bonding kit consists of the following: 1 x earth bonding plate 1 x black hex screw 1 x serrated washer

Solar Mesh Clips with Nut Pack of 60 for 30m of mesh #2: WM172-60-TRADE Simple clip on system designed specifically to keep birds out from under solar arrays Unlike other solar clips the nut is designed to be removable allowing for maintenance of the solar panels Clips recommended every 450mm (18 inches) 2 clips on short edge 3 clips on long edge. Solar clips bind the mesh to the panels without drilling holes or damaging the system. Designed to fit our Solar Panel Mesh (WM133 & WM139). Nearly invisible from the ground Fast easy & highly effective, making solar panel bird exclusion straight forward Mesh Sold Separately

30m Solar Panel Bird Deterrent Mesh - Galvanised Steel and Black PVC Coated #1: WM170-TRADE Galvanised steel mesh, coated with black PVC Prevents birds from nesting underneath solar panels Use in conjunction with our solar panel mesh clips (WM132) to secure the mesh to the return lip on the underside of the solar panels

SolarEdge Home Hot Water Controller, 3kW #2: SMRT-HOT-WTR-30-S2 SolarEdge Home Hot Water Datasheet SolarEdge Home Hot Water Manual SolarEdge Home Hot Warranty *Collections are not permitted due to health & safety regulations* Solar Edge Smart Energy Hot Water maximizes self-consumption by storing excess solar energy as hot water Integrates seamlessly with the complete SolarEdge Home ecosystem, offering a single source for warranty, support and training, to streamline logistics & operations. Automatically adjusts power supplied to the heater, using any amount of available PV power (up to 5.0kW). Wireless communication to the inverter using SolarEdge Home Network, reducing wiring, labor, and installation faults. Built-in water tank power consumption meter. Simple wall mount installation. Suitable for powering purely resistive loads only. Optional temperature sensor for optimized heating.

Solar Mesh Clips Single Use Pack of 60 for 30m of mesh #1: WM173-60-TRADE Simple clip on system designed specifically to keep birds out from under solar arrays These clips are a permanent fixing, once discs have been pushed onto the rod they cannot be removed Clips recommended every 450mm (18 inches) 2 clips on short edge 3 clips on long edge. Solar clips bind the mesh to the panels without drilling holes or damaging the system. Designed to fit our Solar Panel Mesh (WM133 & WM139). Nearly invisible from the ground Fast easy & highly effective, making solar panel bird exclusion straight forward Mesh Sold Separately

Bird Deterrent 30m Solar Panel Bird Exclusion Kit (Galvanized Mesh) #1: WM134-PVC Solar panel exclusion kits keep pigeons and other pest birds out from under solar panels on pitched roofs Everything you need to treat 30m around of solar panels Kit includes wire mesh, specialist solar panel retaining clips and cutting tool 100% effective when properly installed, better than using spikes, chicken mesh or repellent gels Does not pierce roof or solar panel, no leaks no warranty issues with panels Fast and easy to install, no gluing or drilling necessary. For this kit to work the solar panel must have a minimum 20mm return lip on the underside of the frame. Kit Contents: 1 x Solar Panel Weldmesh Roll in Galvanised Steel 60 x Solar Panel Mesh Clips 1 x Standard Wire Cutters 20 x Corner Zip Ties Solar Panel Galvanised Steel Weldmesh Spec: Manufactured from: 16 gauge / 1.60 mm diameter European Grade A Hot Dipped Galvanised wire. Mesh Size: 25mm X 25mm (1" X 1") Roll Width: 200mm (0.66') Roll Length: 30m (100')

Victron SmartShunt 1000A/50mV #17: Victron SmartShunt 1000A/50mV (SmartShunt Only) Victron SmartShunt 1000A/50mV Datasheet*Collections are not permitted due to health & safety regulations* The SmartShunt is an all-in-one battery monitor, only without a display: your smartphone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone or tablet and you can conveniently read all monitored battery parameters, like state of charge, time to go, historical information and much more.Alternatively, the SmartShunt can be connected and read by a GX device. Connection to the SmartShunt is made via a VE.Direct cable.The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is needed but less wiring and clutter is wanted. It is equipped with Bluetooth, a VE.Direct port, and a connection that can be used for monitoring a second battery, midpoint monitoring, or a temperature sensor.The SmartShunt is available in 500A, 1000A, 2000A and 6000A versions.Have a Solar System? See these settings for optimal operation.

Victron Lynx Distributor #17: Victron Lynx Distributor Victron Lynx Distributor Manual*Collections are not permitted due to health & safety regulations* A modular DC bus bar, used to connect batteries to the Lynx DC distribution system, with locations for four DC fuses. The younger brother of the Lynx Distributor - upgrade to this one if you would like LED indicators for each fuse. Part of the modular Lynx distribution system.Victron use the highest grade of components, robust and precise manufacturing procedures, and rigorous testing to ensure consistent high quality. Enclosure material ABS Enclosure dimensions (hxlxw): 290 x 170 x 80 mm Unit weight: 2.2 kg Busbar material: Tinned copper Busbar dims (hxw): 8 x 30mmConnections: M8Protection class: IP22

Fox 10kW K Series Single Phase Hybrid Inverter #2: FE-KH1-10.0 Storage Systems - Hybrid Inverter Fox 10.0kW Datasheet Fox 10.0kW Manual Fox 10.0kW Warranty Fox 10.0kW G100 Certificate *Collections are not permitted due to health & safety regulations* The FoxESS K Series is a stylish 10kW single phase IP65 full hybrid inverter. The Fox K Series uses high voltage batteries for maximum round-trip efficiency, ensuring you get the most out of your solar system. The FoxESS KH10 is easy to install, saving you valuable time on site. The FoxESS Cloud allows for easy remote monitoring and control, making it a breeze to support remotely. Compatible with all Cube & EP5/11 batteries IP65 rated - suitable for outdoor installations Remote monitoring via web portal or smartphone Easy to expand battery capacity Tripple MPPT - ensure optimal solar production High round-trip efficiency of 97% CT clamp is included in the box for zero export control. Specs Weight: 29 kg Rated Power: 10,000 W Min PPT Voltage: 80 V Max PPT Voltage: 500 V DC Startup Voltage: 75 V DC Shutdown Voltage: 75 V Max Input Voltage: 600 V Max DC Power: 15,000 W Max AC Power (5 Minutes): 10,000 W Surge AC Power (1 Second): 10,500 W Max DC Current: 64A Max DC Inputs: 4 Has DC Fuses: 0 Connector: MC4 Included Connectors: 8 Euro Efficiency: 97.4 % Transformer: None MPPT Quantity: 4 Has Integrated DC Switch: Yes  

4mm2 single-core DC solar cable 25m - Black #1: CABLE4-1-25 Cables - DC Cables 4 mm ², single-core, black, 25m NEW H1Z2Z2-K certified 50m solar cable with length label. Manufactured against the latest European Standard EN 50618 and with the harmonised designation H1Z2Z2-K, these Solar DC Cable are specified cables for use in Photovoltaic (PV) systems, and in particular those for installation at Direct Current (DC) side with a nominal DC voltage of up to 1.5kV between conductors as well as between conductor and earth, and not exceeding 1800V. EN 50618 requires cables to be low smoke zero halogen and be flexible tin-coated copper conductors with a single core and cross-linked insulation and sheath. Cables are required to be tested at a voltage of 11kV AC 50Hz and have an operating temperature range of -40oC to +90oC. H1Z2Z2-K supersedes the previous TÆ’Å“V approved PV1-F cable. H1Z2Z2-K PHOTOVOLTAIC CABLE CONSTRUCTION Conductor Flexible tinned copper (Class 5) Insulation Halogen-free cross-linked compound Outersheath Halogen-free cross-linked flame retardant compound The compounds used in these solar cable's insulation and outersheath are halogen free cross-linked, hence the reference to these cables as "cross-linked solar power cables". The EN50618 standard sheathing has a thicker wall than the PV1-F cable version.

SolarEdge Home Battery Home Battery 48V V2 - 3PH Low Voltage 4x 4.6kWh module = 18.4kWh #2: SE-BATTERY-4.6kWH-02-4-18.4 SolarEdge 4.6kWh Datasheet SolarEdge 4.6kWh Manual SolarEdge 4.6kWh Warranty This product contains 4 x SolarEdge Home Battery 48V V2 - 3PH Low Voltage 4.6kWh module BAT-05K48M0B-02 - Three Phase Inverter Connection Only DC coupled battery featuring superior overall system efficiency, generating more energy to store and use for on-grid and backup* power application. Scalable solution that enables to stack up multiple battery modules per inverter for increased capacity (up to 23 kWh). Integrates seamlessly with the complete SolarEdge Home ecosystem, offering a single source for warranty, support and training, to streamlined logistics & operations. Solar, storage, EV charging, and smart devices all monitored and managed by a single app for optimized production, consumption, and backup* power. Includes enhanced safety features for battery protection. Simple plug and play installation, with automatic SetApp-based configuration Weight: 244 kgBattery Type: Lithium IonNominal Energy: 18400 WhDepth of discharge: 90.00 %Voltage: 51 VContinuous Discharge Rate (Normal Use): 5000 WMaximum Discharge Rate (5 Minutes): 5000 WSurge Discharge Rate (15 Seconds): 4096 WMaximum Charge Rate (5 Minutes): 5000 W

GSE In roof Mounting System Portrait tile roof #1: GSE-PORTRAIT-SLATE-KIT GSE Datasheet GSE Manual GSE Warranty Minimum order - 5, must be purchased together with solar panels Please note: The required components ranges greatly depending on the number of panels & layout. To order GSE please include on your order and a quote will be provided based on the layout information you provide or request fo a quote to be provided.   Layout and roof type must be provided following order for the correct design & supply   An integrated photovoltaic panel system"developed by installers for installers"   Compatible with 95% of the framed modules on the market Certified conception and design to allow watertightness, optimized ventilation and fire restistance Easy and quick to install 100% French manufacturing Kit includes: Junction for Top Flashing BLACK Corner Piece (To Join Module to Top Centre Flashings) BLACKTop Right Corner Flashing BLACKTop Left Corner Flashing BLACK IN ROOF - SINGLE END CLAMP V2023 - H16 - STEEL - BLACK Mid Clamp Double V2023 EPDM - H16 – BLACK GSE Clamp Wedges Twin Pack ( 2x Left / 2x Right ) GSE Flashing Hook GSE Joint EDPM Pre Drilled 9mm Self-Tapping Screw + GSE Washer (Pack of 100) Lateral Flashing - UNIVERSAL - 1290MM – BLACK NEW DPO Ubbink UBIFLEX B3 Non-Lead Flashing BLACK 400mm x 12m GSE Metal Top Centre Flashing BLACKGSE portrait frames   Certified and guaranteed for 10 years Designed and manufactured in France, the GSE IN-ROOF SYSTEM is certified by various European bodies.Reliable and resistant, it has been designed to offer the same resistance and longevity as normal roof coverings like tiles, slates or zinc : Resistance to fire Completely waterproof: ensures complete watertightness of the PV system and the roof Optimal ventilation Impact resistance Very important mechanical resistance, compatible with all snow and wind zone In 2022, the GSE IN-ROOF SYSTEM has evolved... In order to keep up with the requirements of the market and to adress the new expectations of more power per roof. The new GSE IN-ROOF SYSTEM, with it two half frames, allows the integration of larger, wider and more powerfull modules.  

SolarEdge Wi-Fi Antenna for Three Phase Inverter with Synergy Technology (1pc) #1: SE-ANT-ZB-WIFI-03 Display - Web Interfaces*Collections are not permitted due to health & safety regulations*SE-ANT-ZB-WIFI-0

GSL Orange Power Cable 1.5 M